For example, to receive only power (1), light brightness (2) and light color (16) and send only power (1), enter the command DevGroupShare 19,1. and are bit masks where each mask is the sum of the values for the categories (listed below) to be shared.
, = set incoming and outgoing shared items (default = 0xffffffff,0xffffffff)
#FAN CONTROL FOR A MAC UPDATE#
255,128,0,0,0 will turn the red channel on at 100% and the green channel on at 50% on an RBG light) or hex color value (#RRGGBB, #RRGGBBWW, etc.)ĭevGroupSend 5=90 128=1 - send an update to set the light brightness to 90 and turn relay 1 on.ĭevGroupSend 193=Buzzer\ 2,3 - send the Buzzer 2,3 command.ĭevGroupSend - set the next fixed color and decrease the brightness by 10.ĭevGroupSend 128=^ - toggle all the relays.ĭevGroupSend 224=NFF0000 - set the color to red locally and inform the group that light channel information is not to be shared until changed.ĭevGroupSend - do not share light brightness or channel status until changed.
If the number of relays is not specified, only relay 1 is setġ29 = No Status Share - DevGroupShare bitmask indicating which items should not be shared until changed.Ģ24 = Light channels - comma separated list of brightness levels (0.255) for channels 1 - 5 (e.g. The number of relays can be specified in bits 24 - 31. To indicate that an item should not be shared with the group until changed again, prefix the value with N.ħ = Light fixed color (0 = white (using CT channels), other values according to Color)ġ0 = PWM dimmer power-on brightness (0.255)ġ28 = Relay Power - bitmask with bits set for relays to be powered on. If is not specified, it defaults to 0xffffffff for the invert operator and 1 for other operators. can be + (add), - (subtract), ^ (invert), & (bitwise AND) or | (bitwise OR). The message sent is also processed on the local device as if it had been received from the network.įor items with numeric values, can be specified as to send a value after performing an operation on the current value. Spaces in must be escaped with a backslash (\). Multiple item/value pairs can be specified separated by a space. The device group name must have been previously set with DevGroupName. If a device group name is not set for a group, the MQTT group topic ( GroupTopic) is used (with the device group number appended for device group numbers > 1). Each 1 bit beeps for 200 milliseconds and each bounded 0 bit pauses for 300 millisecondsĠ = disable Sonoff iFan03 buzzer (default)ġ = use frequency output for buzzer pin instead of on/off signal, for piezo buzzers Number of relay toggles ( blinks) (does not control the status LED)Ġ = blink many times before restoring power stateġ.32000 = set number of blinks (default = 10)Ģ.3600 set duration, in 0.1 second increments, to blink aka toggle Power (does not control the status LED)Ĥ0.1000 = set button debounce time in milliseconds (default = 50)Ģ,3 = Beep twice with 300 milliseconds duration and 100 milliseconds pauseĢ,3,4 = Beep twice with 300 milliseconds duration and 400 milliseconds pauseġ,2,3,0xF54 (0000 0000 0000 0000 0000 1111 0101 0100). List of commands to be executed without any delay in sequence separated by List of commands to be executed in sequence separated by the total length of all these parameters is limited to this size (you will be noted if this limit is exceeded). If you used user_config_override.h at compile time it will revert to those.Īlmost all settings using string parameters (except Rule and MqttFingerprint) share a common area with max 698 chars, i.e. When a command mentions resetting to "firmware default" it means the setting will revert to the one in the flashed binary file. In commands with x.y value parameters use a number from x to y range. Power1 and Power both control first defined power output (usually Relay1) Leave it empty to use the first available. Replace in a command with the appropriate index number. Power1 1 also turns first defined power output (usually Relay1) on dela Power1 True also turns first defined power output (usually Relay1) on Power ON turns first defined power output (usually Relay1) on Instead of 0 you can use off or false and instead of 1 you can use on or true. Power returns the status of first defined power output (usually Relay1)
#FAN CONTROL FOR A MAC HOW TO#
Tasmota provides a powerful control interface using commandsĬommands can be issued using MQTT, web requests, webUI console and serial How to use commands ~Įvery command used without a parameter (payload) returns the current setting. RCWL-0516 microwave radar motion sensor.MLX90640 Far infrared thermal sensor array.MGC3130 3D tracking and gesture controller.
0 kommentar(er)
